hookpopla.blogg.se - Brocade san switch serial connection

#Brocade san switch serial connection how to
#Brocade san switch serial connection serial
#Brocade san switch serial connection manual

#Brocade san switch serial connection serial

Connect the serial cable to the serial port on the switch and to an RS-232 serial port on 3.

Connect to the switch and log in as an administrator. Verify that the switch has completed POST.

And there it is our Switch with DomainID40 is switch05. This is considered as the name/ID of the switch.

FFFC xx is the Address of the Domain Controller xx represents the Domain ID. The Dynamic Ports on Demand (POD) feature automatically assigns POD licenses from a pool of available licenses that is based on the server blade or switch installation. I compare a 4/8 switch, which uses an older style serial cable, with a newer 8/80 switch, which requires a 'straight through' pin-out configuration. What interests us is the ID of the Switch.

In the Please Login dialog box, type the username and password, and then click OK.

Open the web browser, type the IP address of the switch in the address field, and press Enter.

Launch Web Tools directly from a web browser:

Assign the management IP address for the switch:ĭHCP : off Accessing the Brocade switch through Web Toolsīrocade Web Tools is an embedded UI that enables administrators to monitor and manage single or small fabrics, switches, and ports.

To implement it, on the web GUI of the Flex System SAN switch, go to Switch > Advanced Switch Properties.

#Brocade san switch serial connection how to

In the console, configure the serial connection settings as follows: This is a quick guide on how to connect FC3171, a 8Gb QLogic SAN switch within IBM Flex System chassis, to a Brocade 300 SAN switch.

Use HyperTerminal to open the switch console.

Connect one end of the serial cable to the RJ-45 serial port on the switch, and the other end to the serial port on the server (workstation).

Access the Brocade switch through Web Tools.Īssigning the management IP address to the SAN switch esĪssign the management IP address to the SAN switches:.

Assign the management IP address for the switch.

Direct connection to the switch with a serial cable.

#Brocade san switch serial connection manual

Other systems - AIX, Sun - I don't know.After racking and cabling the SAN switches, configure the switches by performing the following tasks: See the Brocade 5100 Hardware Reference Manual and the Fabric OS Administrators Guide (located on. If you have attached MS-Windows systems, they would be fine they don't use the PID. What to do and how depends on what volume manager you are using and whether you are using a pseudo-drive like SecurePath. You may need to do some reconfiguration around this. If you move your EVA connection to a different port in your fabric (or a different switch), then attached HP-UX systems will see any attached LUNs as a "new" device, and the original LUNs as missing. One component of the PID is the domain of the switch. Certain systems, notably HP-UX, use the port ID (PID) for binding the LUNs. This, although still unlikely, would probably be because of a configuration mismatch of one of the items above.Īlso, as for moving your EVA array, be careful with this. The Brocade 6510 switch features up to 48 ports of Gen 5 Fibre Channel technology with specifications. The most likely problem is that the two switches simply won't mesh. The Brocade 6510 represents best-of-class Fibre Channel SAN switching, which is an important asset to the StorageReview Enterprise Storage Lab in order to ensure that network components do not bottleneck storage devices during SAN benchmarks. Disconnect, reboot, and figure out what happened.

The worst possible - albeit highly unlikely - outcome is that the meshing will crash the original switches. Once they mesh with the existing switches, they will inherit that config. Since you have new switches, the default setting should be 1, which is the recomended setting.ģ) the new switches should have no configuration, zoning, or alias information on them. The big things are:ġ) insure that the new switches have a different Domain ID than the existing switches.Ģ) insure that the new switches use the same PID format as the existing switches. FOS-90x-EZSwitch-UG100 User Guide Brocade® EZSwitchSetup User Guide, 9.0. HPE Blog, Austria, Germany & SwitzerlandĪs other described, this is, in general, a fairly simple operation.